| A VR | Add Voice routing (Administrator) |
| A VR ID:xx [par:val] |
It adds a new entry to the table of Fxs/Fxo VOICE routings in the "ID:xx" position. The command can also set eventually indicated parameters to the specified values. Not specified parameters are set to default values.
The table of Fxs/Fxo VOICE routings can store up to 64 entries, therefore the routing identifier value must be in the interval [0 - 63]. The table is not automatically maintained with consecutive indexes, then Fxs/Fxo VOICE routing definitions may not have sequential identifiers.
If an entry with the same identifier is already present in the table, is going to be added, the "VOICE ROUTING ALREADY EXISTS" error message will be shown.
If the table of Fxs/Fxo VOICE routings is full and a new routing is asked to be added, an error message is generated: "VOICE ROUTING TABLE IS FULL, COMMAND NOT EXECUTED".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of Fxs/Fxo VOICE routings are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| C VR | Clear Voice routing (Administrator) |
| C VR ID:xx |
It deletes the specified entry from the table of Fxs/Fxo VOICE routings. The routing identifier must be in the interval [0 - 63].
If the requested entry is not present in the table, the following error message will be displayed: "VOICE ROUTING NOT PRESENT".
Fxs/Fxo VOICE routings, whose identifier is higher than the deleted one, are not decremented because of table contiguity. So, the deleted definition frees a place in the table of Fxs/Fxo VOICE routings, which won't be displayed by the command D VR.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of Fxs/Fxo VOICE routings are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| D VR | Display Voice routing (Administrator) |
| D VR D VR ID:xx |
It shows the table of Fxs/Fxo VOICE routings.
If the identifier is omitted, the command will show all the Fxs/Fxo VOICE routings currently set.
Fxs/Fxo VOICE routing definitions may not have sequential identifiers, that 's the not shown values represent the free places in the table.
Here is an example of the command execution:
[18:14:08] ABILIS_CPX: D VR - Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- ID: NUM: NUMO: GROUP: POO: --------------------------------- 0 1 * # 501 1 2 * # 501 4 160 * # 60 5 162 * # 62
By specifying the Fxs/Fxo VOICE routing identifier, the command will show only the requested routing.
The identifier must be in the interval [0 - 63]. If the requested entry is not present in the table, the message "VOICE ROUTING NOT PRESENT" will be generated.
If the table of Fxs/Fxo VOICE routings is empty, the following message will be shown "*** NO VOICE ROUTINGs DEFINED ***".
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
For a more detailed description of the shown information, refer the Configuration of Fxs/Fxo VOICE connections section.
| S VR | Set Voice routing (Administrator) |
| S VR ID:xx par:val [par:val] |
It sets parameters of the specified Fxs/Fxo VOICE routing to their new values.
The specified Fxs/Fxo VOICE routing identifier value must be in the interval [0 - 63]. If the specified routing is not present in the table, the message "VOICE ROUTING NOT PRESENT" is generated.
If the table of Fxs/Fxo VOICE routings is empty, the following message will be displayed "VOICE ROUTING TABLE IS EMPTY".
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other, starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the table of Fxs/Fxo VOICE routings are not immediately active. For activating them, it is needed to execute the initialization command INIT VR
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| A VG | Add Voice group (Administrator) |
| A VG ID:xx [par:val] |
It adds a new entry to the table of Fxs/Fxo VOICE groups. The command can also set the eventually indicated parameters to the specified values. Not specified parameters are set to default values.
The table of Fxs/Fxo VOICE groups can store up to 15 entries, therefore the specified group identifier must be in the interval [1 - 15]. The group definitions may not have sequential identifiers.
If an entry with the same identifier "ID:xx" is already present in the table, the "VOICE GROUP ALREADY EXISTS" error message will be shown.
If the table of Fxs/Fxo VOICE groups is full and a new entry is going to be added, an error message is generated: "VOICE GROUP TABLE IS FULL, COMMAND NOT EXECUTED".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of Fxs/Fxo VOICE groups are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| C VG | Clear Voice group (Administrator) |
| C VG ID:xx |
It deletes the specified entry from the table of Fxs/Fxo VOICE groups. Specified identifier "ID:xx" must be in the interval [0 - 15].
If the specified group is not present in the table, the following error message will be displayed: "VOICE GROUP NOT PRESENT".
Fxs/Fxo VOICE groups, whose identifier is higher than the deleted one, are not decremented because of table contiguity. So, the deleted entry frees place in the table, which won't be displayed by the command D VG.
If the table of Fxs/Fxo VOICE groups is empty, the following message will be displayed "VOICE GROUP TABLE IS EMPTY".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of Fxs/Fxo VOICE groups are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| D VG | Display Voice group (User) |
| D VG D VG ID:x |
It shows the table of Fxs/Fxo VOICE groups.
If the identifier is omitted, the command will show all the Fxs/Fxo VOICE groups currently set.
Fxs/Fxo VOICE group definitions may not have sequential identifiers, that is the not shown values represent the free places in the table.
Here is an example of the command execution:
[18:14:08] ABILIS_CPX: D VG - Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- ID |1 2 3 4 5 |6 7 8 9 10 |11 12 13 14 15 |16 17 18 19 20 ------------|-------------------|---------------|---------------|-------------- 1 VS:R VPx:|60 61 62 63 . |. . . . . |. . . . . |. . . . . DS:R DPx:|1 2 . . | | | ------------|-------------------|---------------|---------------|-------------- 3 VS:R VPx:|. . . . . |. . . . . |. . . . . |. . . . . DS:R DPx:|. . . . | | | ------------|-------------------|---------------|---------------|--------------
By specifying a Fxs/Fxo VOICE group identifier, the command will show only the requested entry.
The identifier must be in the interval [0 - 15]. If the requested entry is not present in the table, the message "VOICE GROUP NOT PRESENT" will be generated.
If the table of Fxs/Fxo VOICE groups is empty, the following message will be shown "*** NO VOICE GROUPs DEFINED ***".
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
For a more detailed description of the shown information, refer the Configuration of Fxs/Fxo VOICE groups section.
| S VG | Set Voice group (Administrator) |
| S VG ID:xx par:val [par:val] |
It sets parameters of the specified Fxs/Fxo VOICE group to their new values.
The identifier must be in the interval [0 - 15]. If the requested entry is not present in the table, the message "VOICE GROUP NOT PRESENT" will be generated.
If the table of Fxs/Fxo VOICE groups is empty, the following message will be shown "VOICE GROUP TABLE IS EMPTY".
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other, starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the table of Fxs/Fxo VOICE groups are not immediately active. For activating them, it is needed to execute the initialization command INIT VR
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| A VD | Add Voice data port (Administrator) |
| A VD ID:xx [par:val] |
It adds a new entry to the table of data ports for Fxs/Fxo VOICE connections. The command can also set the eventually indicated parameters to the specified values. Not specified parameters are set to default values.
The table of data ports for Fxs/Fxo VOICE connections can store up to 32 entries. Therefore the specified identifier must be in the interval [0 - 31]. The definitions of Data ports for Fxs/Fxo VOICE connections may not have sequential identifiers
If an entry with the same identifier is already present in the table, the "VOICE DATA PORT ALREADY EXISTS" error message will be shown.
If the table of data ports for Fxs/Fxo VOICE connections is full and a new entry is going to be added, an error message is generated: "VOICE DATA PORT TABLE IS FULL, COMMAND NOT EXECUTED".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of data ports for Fxs/Fxo VOICE connections are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| C VD | Clear Voice data port (Administrator) |
| C VD ID:xx |
It deletes the specified entry from the table of data ports for Fxs/Fxo VOICE connections.
The specified identifier must be in the interval [0 - 31].
VOICE data ports, whose identifier is higher than the deleted one, are not decremented because of table contiguity. So, the deleted entry frees place in the table, which won't be displayed by the command D VD.
If the requested entry is not present in the table, the following error message will be displayed: "VOICE DATA PORT NOT PRESENT".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Changes made on the table of data ports for Fxs/Fxo VOICE connections are not immediately active. For activating them, it is needed to execute the initialization command INIT VR.
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
| D VD | Display Voice data port (User) |
| D VD D VD ID:xx |
It shows the table of data ports for Fxs/Fxo VOICE connections.
If the identifier is omitted, the command will show all the data ports for Fxs/Fxo VOICE connections currently set.
The definitions of data ports for Fxs/Fxo VOICE connections may not have sequential identifiers, that is the not shown values represent the free places in the table.
Here is an example of the command execution:
[18:14:08] ABILIS_CPX: D VD - Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- ID: PO: MXBW: CURBW: ----------------------------------- 0 501 NOMAX 0 1 502 64000 15600 3 NONE NOMAX -
By specifying the identifier of a data port for Fxs/Fxo VOICE connections, the command will show only the requested entry.
The identifier must be in the interval [0 - 31]. If the requested entry is not present in the table, the message "VOICE DATA PORT NOT PRESENT" will be generated.
If the table of data ports for Fxs/Fxo VOICE connections is empty, the following message will be shown "*** NO VOICE DATA PORTs DEFINED ***".
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
For a more detailed description of the shown information, refer the Configuration of DATA ports for VOICE connections section.
| S VD | Set Voice data port (Administrator) |
| S VD ID:xx par:val [par:val] |
It sets parameters of the specified data port for Fxs/Fxo VOICE connections to their new values.
The identifier value must be in the interval [0 - 31]. If the specified entry is not present in the table, the message "VOICE DATA PORT NOT PRESENT" is generated.
If the table of data ports for Fxs/Fxo VOICE connections is empty, the following message will be shown "VOICE DATA PORT TABLE IS EMPTY".
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other, starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the table of Fxs/Fxo VOICE data ports are not immediately active. For activating them, it is needed to execute the initialization command INIT VR
The "Not Saved (SAVE CONF)" message is displayed every time the table is modified but not saved with the SAVE CONF command.
The "Not Refreshed (INIT)" message is displayed every time the table is modified but not refreshed with the INIT VR command.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| C VC | Clear Voice connection (Administrator) |
| C VC ID:x |
It forces to clear the specified Fxs/Fxo VOICE connection.
If the requested Fxs/Fxo VOICE connection is not present, the error message "VOICE CONNECTION NOT PRESENT" will be shown.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| D VC | Display Voice connections status (User) |
| D VC |
It shows the Fxs/Fxo VOICE connections that are currently present.
If no Fxs/Fxo VOICE connection is present, the message "NO VOICE CONNECTIONS" is generated.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
Here is an example of the command execution:
[18:14:08] ABILIS_CPX: D VC ID Numi Numo Poi Chi State Grp Poo Cho VrID Sp Bw -- ---- ---- --- --- --------- --- --- --- ---- ------ ------ 0 555 666 60 1 BUSY 1 63 - 0 0 0 1 2 2 61 1 CONNECTED 502 1 4 4800 6200 2 376 20 501 1 CONNECTED 61 2 2 6400 7800
For a more detailed description of the shown information, refer to the Vision of Fxs/Fxo VOICE connections status section.
| C TT | Clear Tone Trace (Administrator) |
| C TT PO:xxx |
It clears the Tone Trace on the requested port. The port identifier must be in the interval [0 - 999] and must correspond to a VOICE port currently present and running.
If the port is not a VOICE port, the error message "COMMAND NOT ALLOWED FOR THAT PORT" is shown.
If the requested port is not present or not properly running this error message will be generated: "PORT NOT PRESENT OR NOT RUNNING".
If the command is successful the following message will be shown: "COMMAND EXECUTED".
If Tone Trace has been activated through the command S TT, the message "TONE TRACE NOT READY" is generated.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| D TT | Display Tone Trace (User) |
| D TT PO:xxx |
It shows the Tone Trace relating to the specified port. The port identifier must be in the interval [0 - 999] and must correspond to a VOICE port currently present and running.
If the port is not a VOICE port, the error message "COMMAND NOT ALLOWED FOR THAT PORT" is shown.
If the requested port is not present or not properly running this error message will be generated: "PORT NOT PRESENT OR NOT RUNNING".
If Tone Trace has been activated through the command S TT, the message "TONE TRACE NOT READY" is generated, while if it is still running and it has not been stopped by the command C TT, the following will be shown "TONE TRACE RUNNING".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| S TT | Set Tone Trace (Administrator) |
| S TT PO:xxx |
It sets the Tone Trace on the specified port. The port identifier must be in the interval [0 - 999] and must correspond to a VOICE port currently present and running.
If the port is not a VOICE port, the error message "COMMAND NOT ALLOWED FOR THAT PORT" is shown.
If the requested port is not present or not properly running this error message will be generated: "PORT NOT PRESENT OR NOT RUNNING".
If the command is successful the following message will be shown: "COMMAND EXECUTED".
If the Tone Trace is running and it has not been stopped by the command C TT, the following message will be shown "TONE TRACE RUNNING".
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| INIT VR | Init Voice Router (User) |
| INIT VR |
It reinitializes the Analogue VOICE Router by reloading the table of Fxs/Fxo VOICE routings, the table of Fxs/Fxo VOICE groups and the table of data ports for Fxs/Fxo VOICE connections.
If the command is successful, the message "COMMAND EXECUTED" will be shown.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
| R ACB | Restart ACB card (User) |
| R ACB |
It reinitializes the driver of the ACB board. If the command is successful, the message "RESTART ACB EXECUTED" will be shown.
If the Abilis CPX version, currently in use, does not support Fxs/Fxo VOICE service, the following message will be shown "VOICE SERVICE NOT PRESENT".
This command works on the file present in the disk. If the disk is not present or a reading errors occur, the following message will be displayed "ERROR LOADING FILE 'xxxx', RESTART ACB NOT EXECUTED", where "xxxx" stands for the file that is needed for correct running of the ACB board.
Print this page