| A ER | Add Enhanced ISDN Routing (Administrator) |
| A ER PR:xx [par:val] |
It adds a new EIR (Enhanced ISDN Router) routing with PR:xx priority and eventually sets the indicated parameters to the specified values. Not specified parameters are set to default values.
EIR routings table can store up to 100 routing definitions, so the priority value must be in the interval [0 - 99].
If a routing with "PR:xx" is already present in the table, it will get "PR:xx+1" priority.
If "PR:xx" is higher than the maximum (highest) priority currently present in the table, new EIR routing priority will be the (maximum) highest incremented by one.
If the EIR routings table is full and a new routing is asked to be added, an error message is generated: "EIR ROUTING TABLE IS FULL, COMMAND NOT EXECUTED".
Changes made on the EIR routings table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| C ER | Clear Enhanced ISDN Routing (Administrator) |
| C ER PR:xx |
It deletes an EIR (Enhanced ISDN Router) routing from the homonymous table. Priority value must be in the interval [0 - 99].
Priority of remaining routings, if higher than the removed one, is decremented because of table contiguity.
If the specified routing is not present in the table, the message "EIR ROUTING NOT PRESENT" is generated. If the table is empty, then "EIR ROUTING TABLE IS EMPTY" will be displayed.
Changes made on the EIR routings table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| D ER | Display Enhanced ISDN Routing (User) |
| D ER D ER PR:xx |
It shows the EIR (Enhanced ISDN Router) routings table. Information is shown in a short format.
This short representation will not display information about parameters set to their default values. Such information is displayed only if the parameters are set to not default values. In this way representation of one EIR routing is usually contained in a row.
If priority is omitted, the command will show all the routings correctly present in the table. Here is an example of the command execution:
[18:56:10] ABILIS CPX: D ER ---+----+---------+--------+--------+--------------------+-------------------- PR |TYPE|NEXT |POI/SR |POO/DS |CDI |CDO | |ID-DT-MC/SP-VOL-LVOL-SC |CGI |CGO | | |SDI |SDO | | |SGI |SGO | |TI1 .. TI5 ------------------------------------------------------------------------------ 0 DATA NO G2 200 * * ------------------------------------------------------------------------------ 1 TR NO G1 G2 * * ------------------------------------------------------------------------------ 2 TR NO G2 G1 * * ------------------------------------------------------------------------------ 3 CtoC NO CLUS_1 CLUS_2 00 * ------------------------------------------------------------------------------
By specifying a priority value, the command will show the routing identified by specified priority. Priority value must be in the interval [0 - 99]. If the specified priority does not match any routing present in the table, the message "EIR ROUTING NOT PRESENT" is generated.
If the EIR routings table is empty, the following message will be displayed "EIR ROUTING TABLE IS EMPTY".
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Configuration of EIR Connections section.
| D ERE | Display Enhanced ISDN Routing in extended format (User) |
| D ERE D ER PR:xx |
It shows the EIR (Enhanced ISDN Router) routings table. Information is displayed in an extended format.
If priority is omitted, the command will show all the routings correctly present in the table. Here is an example of the command execution:
[18:56:10] ABILIS CPX: D ERE
PR:0 TYPE:DATA POI:G2 CDI:* SDI:*
NEXT:N CGI:* SGI:*
POO:200 CDO:* SDO:*
CGO:* SGO:*
TI1:ALL,00:00-23:59 TI2:# TI3:# TI4:# TI5:#
------------------------------------------------------------------------------
PR:1 TYPE:TR POI:G1 CDI:* SDI:*
NEXT:N CGI:* SGI:*
POO:G2 CDO:* SDO:*
CGO:* SGO:*
TI1:ALL,00:00-23:59 TI2:# TI3:# TI4:# TI5:#
------------------------------------------------------------------------------
PR:2 TYPE:TR POI:G2 CDI:* SDI:*
NEXT:N CGI:* SGI:*
POO:G1 CDO:* SDO:*
CGO:* SGO:*
TI1:ALL,00:00-23:59 TI2:# TI3:# TI4:# TI5:#
------------------------------------------------------------------------------
PR:3 TYPE:CtoC SR:CLUS_1 CDI:00 SDI:*
NEXT:N CGI:* SGI:*
DS:CLUS_2 CDO:* SDO:*
CGO:* SGO:*
TI1:ALL,00:00-23:59 TI2:# TI3:# TI4:# TI5:#
By specifying a priority value, the command will show the routing identified by specified priority. Priority value must be in the interval [0 - 99]. If the specified priority does not match any routing present in the table, the message "EIR ROUTING NOT PRESENT" is generated.
If the EIR routings table is empty, the following message will be displayed "EIR ROUTING TABLE IS EMPTY".
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Configuration of EIR Connections section.
| M ER | Move Enhanced ISDN Routing (Administrator) |
| M ER PR:xx PR:yy |
It changes the EIR (Enhanced ISDN Router) routing priority from the value "PR:xx" to the "PR:yy" one.
By consequence its position inside the EIR routings table will be changed. Other definitions present in the table are re-sorted because of table contiguity.
Priority value must be in the interval [0 - 99]. If the specified priority does not match any routing present in the table, the message "EIR ROUTING NOT PRESENT" is generated.
If the routing table is empty, the following message will be displayed "EIR ROUTING TABLE IS EMPTY".
Changes made on the EIR routings table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| S ER | Set Enhanced ISDN Routing |
| S ER PR:xx par:val [par:val] |
It sets parameters of the EIR (Enhanced ISDN Router) routing identified by "PR:xx" to their new values.
Priority value must be in the interval [0 - 99]. If the specified priority does not match any routing present in the table, the message "EIR ROUTING NOT PRESENT" is generated.
If the routing table is empty, the following message will be displayed "EIR ROUTING TABLE IS EMPTY".
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other,starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the EIR routings table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| A EG | Add Enhanced ISDN group (Administrator) |
| A EG ID:xx [par:val] |
It adds a new EIR (Enhanced ISDN Router) group identified by "ID:xx" and it sets the parameters, eventually indicated, to the specified values. Not specified parameters are set to default values.
EIR groups table can store up to 31 definitions, so the identifiers specified must be in the interval [1 - 31].
If an EIR group, whose ID is already present in the table, is going to be added, an error message will be displayed "EIR GROUP ALREADY EXISTS".
If the EIR groups table is full and a new group is asked to be added, an error message is generated: "EIR GROUP TABLE IS FULL, COMMAND NOT EXECUTED".
Changes made on the EIR groups table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| C EG | Clear Enhanced ISDN group (Administrator) |
| C EG ID:xx |
It deletes the EIR (Enhanced ISDN Router) group identified by "ID:xx", if present.
EIR groups table can store up to 31 definitions, so the identifiers specified must be in the interval [1 - 31].
Identifiers of remaining EIR groups, if higher than the removed one, will not decremented because of table contiguity. The deleted definition frees a place in the table that won't be displayed by the execution of the command D EG.
If the specified entry is not present in the table, the error message "EIR GROUP NOT PRESENT" will be generated.
If the EIR groups table is empty, the following message will be displayed "EIR GROUP TABLE IS EMPTY".
Changes made on the EIR groups table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| D EG | Display Enhanced ISDN group (User) |
| D EG D EG ID:xx |
It shows the EIR (Enhanced ISDN Router) groups table.
If the group identifier is omitted, the command will show all the EIR groups correctly present in the table. Groups definitions may not have sequential identifiers, that is the not shown values are free places in the table. Here is an example of the command execution:
[15:46:31] ABILIS_CPX: D EG ID: SC: R: |P1 P2 P3 P4 |P5 P6 P7 P8 |P9 P10 P11 P12 |P13 P14 P15 P16 -----------|----------------|----------------|----------------|--------------- 1 R NOR|280 281 . . |. . . . |. . . . |. . . . -----------|----------------|----------------|----------------|--------------- 2 R NOR|282 283 . . |. . . . |. . . . |. . . . -----------|----------------|----------------|----------------|--------------- 5 P LNA|. . . . |. . . . |. . . . |. . . . -----------|----------------|----------------|----------------|---------------
By specifying a group identifier, the command will show the requested group only, of course if it is present in the table. The specified identifier must be in the interval [1 - 31].
If the requested EIR group is not present in the table, an error message is generated: "EIR GROUP NOT PRESENT".
If the EIR groups table is empty, the following message will be displayed "EIR GROUP TABLE IS EMPTY".
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Configuration of EIR groupssection.
| S EG | Set Enhanced ISDN group (Administrator) |
| S EG ID:xx par:val [par:val] |
It sets parameters of the EIR group identified by "ID:xx" to their new values. Identifier value must be in the interval [0 - 31].
If the requested EIR group is not present in the table, an error message is generated: "EIR GROUP NOT PRESENT".
If the EIR groups table is empty, the following message will be displayed "EIR GROUP TABLE IS EMPTY".
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other, starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the EIR groups table are not immediately active. For activating them, it is needed to execute the initialization command INIT ER
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| D EID | Display remote Enhanced ISDN Router identifiers (Administrator) |
| D EID |
It shows the EIR (Enhanced ISDN Router) cluster identifiers table.
Here is an example of the command execution:
[18:41:46] ABILIS_CPX: D EID +----------+---------+----------+-------+ | Id: | IntRef: | MaxConn: | Used: | +----------+---------+----------+-------+ | CLUS_1 | 1 [01] | 32 | 1 | | CLUS_2 | 2 [02] | 1 | 2 | +----------+---------+----------+-------+
EIR Cluster identifier table can store up to 233 definitions (from 1 to 233). Definitions may not be sequential, that is the not shown values represent free places in the table.
If the table is empty, the message "EID TABLE IS EMPTY" is generated.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Identifiers of remote EIR clusters section.
| S EID | Set remote Enhanced ISDN Router identifiers (Administrator) |
| S EID ID:name MAXCONN:xx |
It makes possible to set the parameter "MAXCONN:" associated to the specified (Enhanced ISDN Router) cluster identifier. This parameter indicates the maximum number of connections on B channels, that can be opened on that (Enhanced ISDN Router) cluster. The "MAXCONN:" value must be in the range [0 -32].
If the table does not contain any entry identifier by the mnemonic "ID:name", the following message will be shown: "EIR IDENTIFIER NOT PRESENT".
If the table is empty, the message "EID TABLE IS EMPTY" is generated.
Changes made on the EIR cluster identifiers table are immediately active. it is not needed to execute any initialization command.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| A TDM | Add TDM switch (Administrator) |
| A TDM PR:xx [par:val] |
It adds a new definition of TDM switch with priority "PR:xx" and it can eventually set the indicated parameters to the specified values. Not specified parameters are set to their default values.
The TDM switches table can store up to 64 definitions, therefore the specified priority value must be in the interval [0 - 63].
The TDM switches table is automatically maintained with consecutive indexes of priority, that is without "empty" places. Therefore every action of deleting or insertion makes the system to reorder all the indexes succeeding the referred one.
If a TDM switch, whose "PR:xx" is already present in the table, its priority will be increased by one, i.e. it will be "PR:xx+1".
If "PR:xx" is higher than the maximum priority currently present in the table, new definition will get the maximum value incremented by one.
If the TDM switches table is full and a new definition is going to be added, the following message will be generated: "TDM SWITCH TABLE IS FULL, COMMAND NOT EXECUTED".
Changes made on the TDM switches table are not immediately active. For activating them, it is needed to execute the initialization command INIT TDM.
| C TDM | Clear TDM switch (Administrator) |
| C TDM PR:xx |
It deletes from the TDM switches table the definition identified by "PR:xx" Priority value must be in the interval [0 - 63].
Priority of remaining switch, if higher than the removed one, is decremented because of table contiguity.
If the specified entry is not present in the TDM switches table, the message "TDM SWITCH ENTRY NOT PRESENT" will be shown.
If the table is empty the following message will be generated: "TDM SWITCH TABLE IS EMPTY".
Changes made on the TDM switches table are not immediately active. For activating them, it is needed to execute the initialization command INIT TDM.
| D TDM | Display TDM switch (User) |
| D TDM D TDM PR:xx |
It shows the current content of the TDM switches table.
If the priority value is omitted, the command will show all the definitions currently present in the table. Here is an example of the command execution:
[16:36:20] ABILIS_CPX: D TDM ---+--------+---------+-------+-----+------------------------------------------ PR:|SERVICE:|MODE: |VSP-ID:|PO: |CH: ---+--------+---------+-------+-----+------------------------------------------ 0 sQ931 OUTGOING - NONE NONE 1 sQ931 BIDIR - 80 1-2 2 sQ931 BIDIR - 80 NONE 3 VSP - 3 NONE NONE 4 VSP - 32 NONE NONE 5 VSP - 1 96 1-31
By specifying a priority, the command will only show the TDM switch requested. Priority value must be in the interval [0 - 63].
If the specified switch TDM is not present in the table, the message "TDM SWITCH ENTRY NOT PRESENT" will be shown.
If the table is empty the following message will be generated: "TDM SWITCH TABLE IS EMPTY".
For a more detailed description of the displayed information, please refer to the TDM switches configuration section.
| M TDM | Move TDM switch (Administrator) |
| M TDM PR:xx PR:yy |
It changes TDM switch priority from the value "PR:xx" to "PR:yy", consequently also it is position inside the table changes and other definitions are sorted again because of table contiguity. Priority values must be in the interval [0 - 63].
If the specified switch TDM is not present in the table, the message "TDM SWITCH ENTRY NOT PRESENT" will be shown.
If the table is empty the following message will be generated: "TDM SWITCH TABLE IS EMPTY".
Changes made on the TDM switches table are not immediately active. For activating them, it is needed to execute the initialization command INIT TDM.
| S TDM | Set TDM switch (Administrator) |
| S TDM PR:xx par:val [par:val] |
It sets the parameters of the specified TDM switch to their new values. Priority value must be in the interval [0 - 63].
If the specified switch TDM is not present in the table, the message "TDM SWITCH ENTRY NOT PRESENT" will be shown.
If the table is empty the following message will be generated: "TDM SWITCH TABLE IS EMPTY".
Changes made on the TDM switches table are not immediately active. For activating them, it is needed to execute the initialization command INIT TDM.
The parameter list, defined in the command, is left to right evaluated: the parameters are set one after the other, starting from the leftmost. Command evaluating will terminate if one the following events will occur:
All the parameters evaluated, before the error occurrence, will get the new value, the other ones will not be changed.
Changes made on the TDM switches table are not immediately active. For activating them, it is needed to execute the initialization command INIT TDM.
| C EC | Clear Enhanced ISDN connection (Administrator) |
| C EC ID:xxx |
It forces to clear the EIR connection identified by "ID:xxx". The connection identifier must be in the range [0 - 255].
If the requested EIR connection is not present, the error message "EIR CONNECTION NOT PRESENT" will be shown.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
| D EC | Display Enhanced ISDN connection (User) |
| D EC |
It shows currently present EIR (Enhanced ISDN Router) connections. Information is displayed in a short format.
Here is an example of the command execution:
[14:40:11] ABILIS_CPX: D EC ID Type Input Output PR State Cgi (Calling Input) Cdo (Called Output) --- ---- -------- -------- -- --------- ------------------- ------------------- 125 TR 291 283 22 CONNECTED 376390774 181 TR 290 280 19 CONNECTED 381650866 376397398 196 TR 290 282 19 CALLING 444687062 376397398
If no EIR connection is running, the message "NO EIR CONNECTIONS" is generated.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Vision of EIR connections status section.
| D ECE | Display Enhanced ISDN connection in extended format (User) |
| D ECE |
It shows currently running EIR (Enhanced ISDN Router) connections. Information is displayed in an extended format.
Here is an example of the command execution:
[14:40:11] ABILIS_CPX: D ECE
ID:125 TYPE:TR POI:291 GPI:# POO:283 GPO:# PR:22 ST:CONNECTED
CGI: CGO:
SGI: SGO:
CDI:376390774 CDO:376390774
SDI: SDO:
ID:181 TYPE:TR POI:290 GPI:# POO:280 GPO:# PR:19 ST:CONNECTED
CGI:381650866 CGO:381650866
SGI: SGO:
CDI:376397398 CDO:376397398
SDI: SDO:
ID:197 TYPE:TR POI:290 GPI:# POO:282 GPO:# PR:20 ST:CALLING
CGI:3486508535 CGO:3486508535
SGI: SGO:
CDI:376396548 CDO:376396548
SDI: SDO:
If no EIR connection is running, the message "NO EIR CONNECTIONS" is generated.
If the Abilis CPX version, currently in use, does not support EIR services, the following message will be shown "EIR SERVICE NOT PRESENT".
For a more detailed description of the displayed information, please refer to the Vision of EIR connections status section.
| INIT ER | Init Enhanced ISDN Routing (User) |
| INIT ER |
It refreshes the EIR routings table and EIR groups table, according to the changes made on the definitions.
If the command is successful, the message "COMMAND EXECUTED" will be shown.
If the EIR services are not supported by Abilis CPX version currently in use, the following message will be shown "EIR SERVICE NOT PRESENT".
| INIT TDM | Init TDM switches table (User) |
| INIT TDM |
It refreshes TDM switches table, according to the changes made on the definitions.
If the command is successful, the message "COMMAND EXECUTED" will be shown.
If the EIR services are not supported by Abilis CPX version currently in use, the following message will be shown "EIR SERVICE NOT PRESENT".
| INIT EIR | Init Enhanced ISDN Router (User) |
| INIT EIR |
It reinitializes the EIR Router. This procedure is not immediate; usually it can take some minutes to be executed.
If the command is successful, the message "COMMAND EXECUTED" will be shown.
Here is an example of the command execution:
[17:48:12] ABILIS_CPX: INIT EIR INIT EIR IN PROGRESS, THIS MAY TAKES FEW MINUTES... COMMAND EXECUTED
If the EIR services are not supported by Abilis CPX version currently in use, the following message will be shown "EIR SERVICE NOT PRESENT".
| R EBIB | Restart EBIB card (User) |
| R EBIB |
It reinitializes all the VOICE compression modules on the EBIB board.
If the command is successful, the message "RESTART EBIB EXECUTED" will be shown.
This command works on the file present in the disk. If the disk is not present or a reading errors occur, the following message will be displayed "ERROR LOADING FILE 'xxxx', RESTART EBIB NOT EXECUTED", where "xxxx" stands for the file that is needed for correct running of the EBIB board.
If the EIR services are not supported by Abilis CPX version currently in use, the following message will be shown "EIR SERVICE NOT PRESENT".
| R EPIB | Restart EPIB card (User) |
| R EPIB |
It reinitializes all the VOICE compression modules on the EPIB board.
If the command is successful, the message "RESTART EPIB EXECUTED" will be shown.
This command works on the file present in the disk. If the disk is not present or a reading errors occur, the following message will be displayed "ERROR LOADING FILE 'xxxx', RESTART EPIB NOT EXECUTED", where "xxxx" stands for the needed file for correct running of the EPIB board.
If the EIR services are not supported by Abilis CPX version currently in use, the following message will be shown "EIR SERVICE NOT PRESENT".
Print this page